Tech24 Deals Web Search

Search results

  1. Results from the Tech24 Deals Content Network
  2. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. The French units roughly correspond to the outer circumference of the catheter (see table below).

  3. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside diameter).

  4. Image sensor format - Wikipedia

    en.wikipedia.org/wiki/Image_sensor_format

    In digital photography, the image sensor format is the shape and size of the image sensor . The image sensor format of a digital camera determines the angle of view of a particular lens when used with a particular sensor. Because the image sensors in many digital cameras are smaller than the 24 mm × 36 mm image area of full-frame 35 mm cameras ...

  5. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  6. Scale length (string instruments) - Wikipedia

    en.wikipedia.org/wiki/Scale_length_(string...

    Cellos exist in a smaller range of sizes than violins, with 4/4, 3/4, 1/2, 1/4, 1/8, and 1/10 being reasonably common. As with the violin, the Stradivarius scale is regarded as standard for orchestral work; This is about 27.4 inches (700 mm). Violas are commonly described in terms of their body length rather than by a fraction. There are two ...

  7. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    From 1.0 through 2.95 mm, sizes are defined as follows, where N is an integer from 10 through 29: N · 0.1 mm; N · 0.1 + 0.05 mm; From 3.0 through 13.9 mm, sizes are defined as follows, where N is an integer from 30 through 139: N · 0.1 mm; From 14.0 through 25.0 mm, sizes are defined as follows, where M is an integer from 14 through 25: M ...

  8. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    British Standard Whitworth. British Standard Whitworth ( BSW) is an imperial-unit -based screw thread standard, devised and specified by Joseph Whitworth in 1841 and later adopted as a British Standard. It was the world's first national screw thread standard, and is the basis for many other standards, such as BSF, BSP, BSCon, and BSCopper .

  9. Thousandth of an inch - Wikipedia

    en.wikipedia.org/wiki/Thousandth_of_an_inch

    1 thou is equal to: 0.001 international inches (1 international inch is equal to 1,000 thou) 0.0254 mm, or 25.4 μm (1 millimetre is about 39.37 thou) History of usage. The introduction of the thousandth of an inch as a base unit in engineering and machining is generally attributed to Joseph Whitworth who wrote in 1857: